free analytics for godaddy

Residential Boiler Repair Services in Raleigh Area

Are you cold and uncomfortable because your Raleigh, NC area boiler is failing to function? Call Pipetechs Plumbing at (919) 293-1221 and get efficient boiler repair services today! Save money using our online coupons and specials.

boiler repair Service Contractor Raleigh NC area

Some of the largest volume of service calls we get are regarding boiler repair. Boilers don’t usually just quit overnight, often there are telltale signs of a problem long before your unit packs it in. For customers in the Raleigh, NC area are Pipetechs Plumbing is here to help. Our expert technicians off extensive boiler repair services and can get the boiler in your home back in working order in no time. Our past work speaks for itself, so see what our customers have to say here!

What Causes Boiler Problems?

There are many reasons why a boiler might start acting up. If the boiler fuels the heating system, property owners may not notice a problem until they fire it up for the cold weather season. Here are some of the most common boiler issues and the possible problems behind them.

Noise
Noises in a boiler can range from pings and bangs to a low, rumbling noise. The main culprit is either air trapped somewhere in your system or low water pressure, which could be caused by a leak or a faulty pressure relief valve. Kettling is the phenomenon that results in that rumbling noise, and it’s caused by a buildup of lime.

Leaks
The cause of a leak depends on the location. Sometimes it’s a loose or faulty valve, other times a seal or pipe needs replacement. In other more serious cases, the leak can stem from damage to the boiler itself. Wear and tear around the unit can culminate in a serious water leak.

Thermostat or Unit Turns Itself Off
In the first case, it’s usually time to replace the thermostat. If the boiler itself keeps switching off, the problem is usually due to low water pressure, or the water is blocked by a closed valve. Another potential source is lack of air circulation or an improperly working or broken water pump. An inaccurate or faulty thermostat can also cause the boiler to turn on and off at the wrong time.

How Often Should You Maintain Your Boiler?

A boiler should be serviced once a year, usually before the start of the cold season. The specifics of a standard boiler service depend on the type of boiler and the fuel used to keep it running; servicing usually takes about an hour. Annual servicing helps ensure that your boiler is safe and functioning properly. Standard yearly maintenance can detect problems early on and help avoid more costly repairs later.

How Long Do Boilers Last?

Boilers can last for many years, if they’re serviced regularly by a qualified technician and used according to manufacturer’s specifications. In general, manufacturers state that a boiler should last anywhere from 10 – 15 years, though there have been tales of older models still going strong at the 25-year or better mark. Basically, if the cost of maintaining your boiler over the years begins to be higher than the cost of replacing it, it’s time to get a new one. At Pipetechs Plumbing our expert technicians can perform the necessary maintenance services to extend the life of your homes boiler as much as possible.

Why Choose Pipetechs Plumbing?

Don’t wait until your boiler is on its last leg for servicing. If you notice problems, a quick call to us is all it takes to set it right. Our technicians are on call and ready to help get your boiler back in working today. We perform thorough services that will provide you with peace of mind for years to come.

Are you in need of boiler repair or maintenance services in the Raleigh, NC area? Call Pipetechs Plumbing at (919) 293-1221 and schedule an appointment with our expert technicians today!

 
Warning: Unknown: open(/home/content/72/4563572/tmp/sess_8ldgj18lhn2k7gndo3fidu67l3, O_RDWR) failed: No such file or directory (2) in Unknown on line 0

Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct () in Unknown on line 0